How do you hook up a tub drain, 7 bathtub plumbing installation drain diagrams

How to Install a New Bathtub - dummies

January 2020

Carefully flip the tub on its side. Start by removing the screws that secure the overflow faceplate. Open the access panel that hides the tub drain rough-in.

Loosen the center screw if you have a lift-and-turn drain. Wipe away the excess sealant. Instruct your friend to place the overflow hold down plate into position and hand-fasten it with the provided screws. Kristi Waterworth started her writing career in as a journalist for a local newspaper.

You can find drain keys online and at home improvement stores. All you need to do is rotate the stopper, or the part that moves up and down to open and close the drain. Did this article help you? Cookies make wikiHow better. Spread a pencil-sized bead of putty around the rim of the new flange.

Bathtub Plumbing Installation Drain Diagrams

How do you hook up a tub drain

The most difficult part of installing the tub itself is hooking up the bathtub drain to the rough plumbing. If there is no access to the drain from behind or below, and your tub is sitting in its permanent spot, it is best to consult an expert to hook-up your drain. Hooking Up a Bathtub Drain.

Add some water to the tub to test the seal. Install the stopper and overflow lift rod according to package directions. Things You'll Need Screwdriver. From start to finish, installing a new drain should only take some elbow grease and an hour of your time! Tip It is vital that your drain and rough-in line up exactly.

The linkage connects the lever to a plunger, which drops down to stop the tub when the lever is down. About the Author Kristi Waterworth started her writing career in as a journalist for a local newspaper. Compare the two figures, if they match you are ready to go. Unscrew the exposed drain flange with a drain key or pliers.

Related articles

Give them another half turn with the slip-joint pliers. Owners of older homes frequently dream of upgrading their bathtubs. Roll out a long, thin strand of plumber's putty about the size and thickness of a pencil. Feed it into the overflow pipe, screw the overflow faceplate onto the opening, then screw the new drain plate onto the flange. On a tub drain, it usually goes on top, since a tub drain normally screws down and into a receiver.

Slide a new gasket into the opening, then screw in the new flange. For a lower maintenance option, go with a lift-and-turn stopper. Turn a foot lock stopper counterclockwise to take it out of the drain. Warnings If you notice rusting, mildew, or water pressure problems when you attempt to replace a drain, matchmaking adult contact a plumber.

Hooking Up a Bathtub Drain

Take off the overflow plate, and pull the linkage rod and plunger out of the overflow hole. Sit the tub upright before tightening the screws all the way down. Let it sit for an hour, then go back and see if any water drained. Place the tub into the installation location and measure these locations again, but from the inside of the tub.

How to Install a New Bathtub - dummies

How do you hook up a tub drain

Slide a strong screwdriver between the handles, and use it like a lever to turn the flange counterclockwise. Take care not to damage the tub's enamel and avoid using harsh, give me a abrasive cleaning products. Click here to share your story.

The drain flange, or drain basket, is the body that connects the tub and stopper to the waste pipe. Article Info This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. After removing the old stopper, take out the old drain flange, or the housing that connects the tub and drain to the pipe below.

How do you hook up a tub drain
  • If your new drain came with a rubber gasket, place it over the drain opening.
  • The gasket is a rubber ring that helps create a waterproof seal between the flange and waste pipe.
  • The putty will help create a watertight seal.
  • Open the handles as wide as possible to create a handle and tighten the drain clockwise.

How to Install a Tub Drain 10 Steps (with Pictures) - wikiHow

Twist or screw on the new stopper, if necessary. Keep them in a safe place until you reinstall the drain. Already answered Not a question Bad question Other. Thread the linkage through the overflow hole if you have a lever drain. On most any sink drain, the gasket goes under the sink, male since the sink's receiver is screwed against the drain.

How do you hook up a tub drain
  1. Then, using a screwdriver, turn the screw counterclockwise and lift the stopper out of the drain flange.
  2. Purchase a new drain assembly online or at your local home improvement store.
  3. Apply plumber's putty or silicone caulk to the underside of the top section of the drain and push it into the drain hole on the tub.
  4. Fit the gasket over the portion of the drain that protrudes out of the bottom of the tub, followed immediately by the drain ell.
  5. It may take several attempts to get this right.
  6. If necessary, wipe away any stubborn residue with rubbing alcohol.

How to Install a New Bathtub

How do you hook up a tub drain

Home Guides

Pull up as you twist it counterclockwise until it lifts out of the drain flange. Measure the exact location of the drain and overflow relative to the tub installation and record the measurements. Include your email address to get a message when this question is answered.

Wedge another gasket between the overflow ell and the overflow opening on the tub. If in doubt, pull the tub and realign without the tailpieces installed. No matter the reason, bathtubs are added and replaced by homeowners on a regular basis. You might just want to banish all traces of the decorating schemes of the s, driving times supercar or need to add functionality or ease of cleaning. This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness.

7 Bathtub Plumbing Installation Drain Diagrams

Foot lock stoppers are the simplest type of drain mechanism. Hold the drain ell in place with one hand. Insert the handles of your pliers into the section of the drain inside the tub. Lift-and-turn drains and some foot lock drains may have a screw in the center of the stopper that holds it in place. It is the most difficult part of the installation.

  • House arrest dating sites
  • Alphabet of dating
  • Usa ice dancers dating
  • Best live dating sites
  • How often should a guy text you when dating
  • Lds dating sites australia